e

The carburettor assy (К22Г-1107000) 20-1107010-Е for GAZ M20 Pobeda Warszawa

# 20-1107010-Е refurbished
25
#23-58А
Spring of the lever of a drive gear of an air shutter
21
#К22-1107230
Flap air assy
23
#К22-1107240-А
Shaft, choke, assy
24
#23-51А
Spring of a shaft of an air shutter
26
#К22-1107250
Lever, choke operation, assy
22
#23-54
Bracket of pull-rod of an air shutter
27
#Н00113
Screw M4x0,7x8
1
#К22-1107048-А
The lever of a drive gear of the clown of the minimum gas
3
#К22-1107160
Disperser of the accelerating pump assy
4
#К22-1107320
The carburettor case top with a tube assy
5
#23-55
Clamp of a bracket of pull-rod of an air shutter
6
#К22-1107030
The choke tube assy
7
#К49-1107330
Valve, fuel feed, assy
29
#23-27
Nut of fastening of a rod
8
#14-42Н
Shaft of a hinge strain of a floater
30
#6-19
Washer shaped
9
#К22-1107600-А
Floater with a hinge strain assy
31
#К22-1107122
Spring
28
#К22-1107120
The accelerating pump assy
32
#К22-1107050
Pull-rod of the accelerating pump with a connecting plate assy
10
#К49-1107412
Collet of the accelerating pump
33
#К22-1107130
Piston with a rod of the accelerating pump assy
11
#К49-1107331
The valve delivery the accelerating pump
34
#К22-1107450
Valve, economizer, assy
12
#К22-1107085
Carburetor Gasket Set K22
$ 13,26
35
#К22-1107440
The valve return the accelerating pump assy
13
#23-53
Pull-rod of a drive gear of the clown of the minimum gas
37
#К49-1107088-А
Disperser layer pad
38
#К22-1107028
Main jet disperser
14
#К22-1107420
The case of a float chamber of the carburettor with caps assy
36
#К49-1107409-1
Jet, slow running
39
#К49-1107087
Layer pad of the block of orifice plugs
15
#К22-1107086А
Gasket
$ 2,21
40
#К22-1107027
The block of orifice plugs
41
#Н01747
Washer 18,2 fibre
16
#К22-1107560
The case of a blending chamber of the carburettor assy
42
#К49-1107150
Needle adjusting assy
43
#К-49-1107153
Epiploon adjusting needles
45
#К22-1107048
The lever of a drive gear of the accelerating pump
17
#К22-1107531
Flap the throttle
44
#К49-1107154
Nut of Epiploon
46
#К22А-1107046
Pull-rod of a drive gear of the accelerating pump
18
#23-68А
The clown of the minimum gas
47
#К22-1107503
Screw, adjusting, slow running
19
#К22-1107542
Throttle valve shaft
48
#Н07103
Spring of an adjusting screw of idle running
20
#К23-1107063С
The lever of a shaft of a throttle valve assy
51
#291790-П
Hairpin (1М10х1 and М10х1,5) х36 carburettor fastenings
49
#Н07121
Spring of Thrust screw
50
#11-9447
Gasket between carburettor and inlet pipe

Enter your name and mobile phone. Our manager will contact you soon

Thank you for order,our manager will contact you soon.

Order number #

Your order:
The carburettor assy (К22Г-1107000)

The carburettor assy (К22Г-1107000)

refurbished # 20-1107010-Е
-+
$385,16
$385,16
How does restoration work?

During operation of the carburetor during overheating, physical deformation of the elements of its upper and middle parts takes place (especially in the places of their screw and bolt connections). The carburetor body "leads" and the mechanical moving parts begin to wedge. The operation of the carburetor becomes unstable and leads to problems with starting and operating the engine.
To eliminate all existing mechanical defects in the carburetor, a comprehensive technology for its restoration (restoration) with the maximum possible preservation of all native original parts and fixing material (hardware) was developed in practical experience.
The list of works of a complete technological process for the restoration of a carburetor includes the following types of work:
1. Technical diagnostics of all mechanical defects and carburetor damage.
2. A complete detailed disassembly of the carburetor - consists of many parts and fasteners.
3. Replacing worn out gaskets, jets and carburetor fasteners.
4. Grinding and adjusting gaps and irregularities on the horizontal surfaces of the upper, middle and lower parts of the carburetor body.
5. Processing of all parts elements with solvent 646 from soot, soot and oily scale.
6. Heat treatment of all parts at a temperature of 120 - 140 degrees. for blurring chemical fatty residues.
7. Cleaning and purging all internal throughput channels and carburetor holes.
8. Sandblasting of all elements of parts and components of the carburetor with quartz sand with a fine sieving structure for soft surface treatment of carburetor parts (especially the case).
9. Rinsing and cleaning fuel and air jets, air dampers, as well as pressure valves and float chambers in a 10 percent solution of edible citric acid (cleans all brass parts of parts to their original shine).
10. Galvanic coating of the surface of all parts with rainbow zinc (anodizing) 3-5 microns thick.
11. The assembly of all components, fixtures and parts of the carburetor in a single unit.
12. Adjustment of mechanical rods and adjusting elements for the comprehensive adjustment of all carburetor assemblies.
Customer reviews (0) Add feedback
CATEGORY